Hello everyone,
I am freehanding a sweater out of granny squares using a 3.00 mm hook and fingering weight yarn. I am estimating I need about 60 squares. It is going to be checkered so about 30 squares in each color. Now I have no problem with making squares, I enjoy it. My problem is the sewing, the ribbing once its sewn, and if I should add a lining or not. I feel like I can figure out the ribbing on my own if I attempt it a few times, so I’m not too worried about doing it, but I’m not too sure what stitch I should use. I want the ribbing to be about 2 inches (5.08 cm) around the wrists and bottom of the sweater, and 1 inch (2.54 cm) at the collar, so I’m not sure if I should use tall stitches or several rows. Now the sewing, I am terrible at sewing granny squares together. I have no clue what sewing stitch to use, last time I did it the sewing stitches came apart and the project dismembered itself. Does anyone have tips for doing this? My project is about 6 squares up by 10 squares around for my body. Also, should I sew in a lining? If so, what material do I use? How do I even do that? Should I use a machine?
Thank you,
Zod/Jay
20 Likes
i’ve never made a granny square sweater before…but maybe a double or half triple crochet? or you could do scalloped edges!!
also maybe a double border? i’ve never made one before but I’ve seen it, where you tuck your outside ends in them so you don’t have to sew them :3
4 Likes
Oh there’s this weird technique that you can use to make ribbing.
Basically you join directly to the finished piece, then chain the length you want to rib plus 2 sts for turning HDC, and you blo hdc down the chain, join join back to the piece, turn, and blo hdc back down the length of the chain. Rinse and repeat. It’s my personal favorite way to add ribbing.
6 Likes
well it depends what yarn type your using, if its acrylic then u should def add a lining bc acrylic can sag over time. for the lining, you could measure out a fabric that you want it to be, then either hand sew or machine sew it to the inside of the sweater?
2 Likes
Hi Jay! This is such a fun project — a checkered granny square sweater in fingering weight is going to look so neat. A few thoughts:
Joining: Skip the yarn needle if your sewn seams keep popping, and try a crochet join instead — slip stitch or single crochet through the back loops only of each square, using your 3.00 mm hook. It flexes with the fabric and basically cannot pull apart the way sewn seams can. Work with the wrong sides facing out so the seam sits flat on the inside. Also, block your squares first so they are all the same size; uneven squares put extra stress on the seams.
Ribbing: For fingering weight, front-post/back-post ribbing (alternating FPDC and BPDC) gives that classic knit-look rib with great stretch. Join your yarn right at the edge of the squares and work into the edge stitches, so there is no separate sewing needed. For 2 inches at the hem and cuffs you will need roughly 8–10 rows of dc ribbing, and 4–5 rows for the 1-inch collar. Half double crochet makes a denser rib if you want something sturdier.
Lining: With fingering-weight granny squares the fabric will be a bit see-through and stretchy, so a lining is worth it. A lightweight cotton jersey or tricot works best because it stretches along with the crochet. Cut it a touch smaller than the finished panels, then hand-sew it in with a whipstitch — just tack it at the neckline, armholes, and hem so the layers can move independently. A machine zigzag stitch works too if you have one.
Cannot wait to see how the checkerboard turns out!
1 Like
So from my experience in sewing granny squares together, I would avoid sewing them together. I agree with @elenaHart that crocheting them together is a more secure and enjoyable way to join granny squares. I do the slip stitch method or join-as-you-go technique.
For the ribbing, I use the same technique that Mangolemmon939 mentioned, however I use a sc instead.
PS: sorry mango I forgot you don’t like being tagged. 
2 Likes
Thank you so so so much!! This was really helpful!
If you go into the stitch index it shows you how to do ribbing. But usually ribbing is done practically the same way you chain the length you want it plus one. For example you would do 13 stitches (12+1). The you need to decide the stitch you can do hdc single crochet or slip stitches (dont recommend haha)
So if you do single crochet you would do your chain 13 the skip the first stitch and single crochet back then single crochet back loop only all the way to the 12th stitch chain one and return. When you get to the body of the work you will slip stitch 1 or 2 (depending on if you want to pull the sleve or bottom a bit tighter) then turn your work and blo to the top.
The joining: you dont have to sew the squares together you can single crochet or slip stitch them. Which will give you a border around the squares. If you want them to be flat and flush against each other whip stitch or ladder is best as they are invisible. Good luck hope thos helps.
I hope this makes sense im terrible at explaining crochet
1 Like
you dont have to sew a lining if you dont want to. if you dont like how the crochet feels on your body, i would see a lining. you would probably be better off seeing it with a maching or by hand, but id be cautious of your crochet getting caught in the needle
1 Like
and also crochet the squares together dont sew them
1 Like